This master thesis is a study of anaerobic thread lockers and is done in cooperation withÖhlins Racing AB, which is a Swedish manufacturer of vehicle suspensions.The suspension in vehicles is constantly exposed to high vibration levels and a suspensionunit has several screw- and cylindrical joints. As an extra safety precaution so that thecomponents in the suspension doesn?t fall apart when using the vehicle, an anaerobicthreadlocker is added in these joints. The handling of these threadlockers is not totallyharmless and could lead to allergic reactions, and therefore there are Swedish laws to limit theuse of these. However, new types of anaerobic threadlockers have recently been launched onthe marked that are not considered under this law.

This thesis has been adjusted because some parts are classified, some sentences might have been changed. Electric bikes are a convenient mode of transport, a good choice when long distances or tough slopes can be an obstacle.The goal of the project was to create a prototype on a locking mechanism with an inductive charger for electric bikes.The idea behind the project was to develop a user-friendly locking mechanism, where the bikes would be charged inductively when they were locked. To implement the project facts about induction, battery charging and locking devices was needed to be acquired. Circuits for induction charging were created and a lock device was constructed. A microprocessor was used to control the entire system.A prototype was designed with a locking device and an inductive charger fixed in a bike rack.The entire project became very wide which resulted in that not all of the parts of the project could be completed.

This thesis has been adjusted because some parts are classified, some sentences might have been changed. Electric bikes are a convenient mode of transport, a good choice when long distances or tough slopes can be an obstacle.The goal of the project was to create a prototype on a locking mechanism with an inductive charger for electric bikes.The idea behind the project was to develop a user-friendly locking mechanism, where the bikes would be charged inductively when they were locked. To implement the project facts about induction, battery charging and locking devices was needed to be acquired. Circuits for induction charging were created and a lock device was constructed. A microprocessor was used to control the entire system.A prototype was designed with a locking device and an inductive charger fixed in a bike rack.The entire project became very wide which resulted in that not all of the parts of the project could be completed.

The task given to us was to develop an industrial wheel with new thinking in terms of fresh design and construction, with the ability to brake. While the produced wheels of today only own the property of total braking, a wish was made to integrate the ability of directional locking.The time spent working with the project has been filled with multiple sketches of ideas and function analysis.Choices of material and ways of construction have been verified by calculations, tests and prototype building. The goal of this thesis has been to develop a unique caster with well thought-out design that would be adaptable to different areas of applications.The result was a hubless wheel with the ability of directional locking before total braking.A prototype of the wheel has been made to show the design and functions..

In this paper the possibilities to replace metal with plastic in products for the building industry were looked into. The first part was a market examination where several suitable products were found. After evaluation the door latch for in-house doors was selected to be re-designed to better suit the properties of plastic.New types of mechanisms were designed with different functions that use the benefits of plastic materials. Models of these mechanisms were developed to evaluate their function. The components in the different mechanisms were adapted for manufacturing with injection moulding.To confirm that the plastic material could handle the appearing stresses calculations on the most vulnerable parts were carried out.

This diploma work has been based on finding a solution to Hälsoteknikcentrum i Halland. The task was to design the wheels of a wheelchair gear, so they can put on and remove with a locking feature.I have sketched out the solution and drawn up in Catia v5, which will be handed over to health technology centers for accounting.  .

This master thesis is commissioned by Permobil AB. The report describes thoroughly the developing process of an adjustable backrest for wheelchairs. The target group for the backrest are people that suffer from scoliosis or other spinal diseases. Because of insufficient pressure distribution usage of traditional backrests is not an option for them.The current solution has got a frame that is made by several adjustable links that is held in place by friction. Between the links velcro tapes are attached that is adjusts the depth.

Bakgrund. Vid tumörresektion i de orofaryngeala vävnaderna, utförs mandibulotomi för att skapa åtkomst och möjliggöra kirurgiskt avlägsnande. Allvarliga komplikationer har rapporterats i litteraturen och bidragande orsaker är den kirurgiska tekniken, strålningsterapin samt en inskränkt näringstillförsel till mandibelkroppen. Syfte. Syftet med denna studie var att undersöka om bevarande av periost vid utförande av mandibulotomi, leder till färre patienter med komplikationer relaterade till mandibulotomin.. Metod. Patienter som genomgick mandibulotomi mellan 2003-2012 vid Skånes Universitetssjukhus granskades retrospektivt.

In this project forging of aluminum alloy Al 6026 T9 has been performed in the temperature range of 400 °C ? 470 °C. The alloy which was in the shape of a cylindrical billet was formed in a press with the aim of analyzing the effect of different forging temperatures and required press load for optimal die filling. The component?s dimensions were later measured and compared to a reference piece.

This report will present athesis on behalf of Eleiko Sports AB and carried out by two students at the InnovationEngineering (University of Halmstad). In this report the project participants willdescribe the project background along with the current product issues andneeds. A clear structure for participants, stakeholders and information flowbetween these parts will be included in this report so that you can clearly seethe areas of responsibility. The report includes a timetable which the grouphas worked along and also methods used. In the development process you will beable to read about how the students in an interdisciplinary way have used themethods and come up with an entirely new product.

The thesis project is accomplished during winter and spring 2008 at Karlstad University at the faculty of technology and science. The tutor at Karlstad University is Nils Hallbäck and the examiner is Hans Johansson. Rolls-Royce at Kristinehamn in Sweden is the initiator for the project. The thesis project title is design of the blade bolt joint on Kamewa CPP. CPP stands for controllable pitch propeller.

Highland Group AB was helping a customer of theirs to create an All-Terrain Vehicle (ATV), a project Highland has never been involved with before. For the wishbone arms of the wheel suspension, traditional manufacturing methods and tubes with cylindrical or square shaped cross section was preferred. We performed a simulation where the ATV was driving on a bumpy road too see the forces involved. With the results we proceeded to calculate the strength of the concepts to find out which is best suited for the tough environment in which the ATV is used. The concept that turned out to be the best was a wishbone made of circular cross section, which had good structural strength and did fulfill the demands that we required for the construction.

This degree project was conducted in collaboration with Gremo AB located in Ätran.The aim of the project was to develop a solution to secure quality and to help assemblingthe locknut holding the vertical hinge on the harvesters and foresters from Gremo.At this time the nut is assembled manually by the aid of an overhead crane. The nut istightened differently from time to time, and there was no specified torque to which it istightened. Another present problem was the locking washer which sometimes getsdamaged during assembly, when this happens the procedure has to be started over fromthe beginning. The current assembly procedure is very time consuming and lengthy forthe employees.Our task was to design a machine that could tighten the nut to a specified torque with amargin of error of ± 3%. The assembly procedure will be held simple and the timerequired at a minimum.The project started by developing several principle solutions, the one solution that bestmatched our specifications were developed to a primary solution.Today we have started manufacturing and assembling our prototype.

The project Easy Battery Handling - EBH has been carried out in our auspicial and completedfor Devantini Corporation, a development company in Halmstad with its main concern inenvironmental friendly innovations.EBH has solved one of many technical challenges in one of Devantini corporation?s largerprojects. This main project involves the development of an electric powered formula racingcar. The part of this car that involved EBH was the battery handling to guarantee safe andquick battery exchanges during pit-stops.The solution became an entire battery module, hanging on the side of the car on two spearspointing out from the car. The batteries are exchanged by a specially designed trolley that isinserted under the battery module.

Fuel pellets are a refined bio fuel mostly consisting of residues from sawmills and wood industry. At Rindi Västerdala AB's combined bio energy plant in Vansbro fuel pellets are produced, while the waste heat from the process is used for district heating. The pellets are produced from sawdust, wood shavings and dry wood chips that is dried, milled and pressed into small cylindrical rods. The advantage of refining the wood material in this manner is that the energy value is greater per unit volume and unit weight, thereby the cost of transportation per energy unit is reduced. Also, less storage space is needed.Pellet manufacturing is a complex process since many parameters affects the final results.